Franklin Collinear Antenna 2 Levels Different Sides using Array Method 4 Stacking Units 360ᵒ with Integrated Reflector and Power Combiner for ADS-B S-Receiver Mode
DOI:
https://doi.org/10.14203/jet.v21.146-153Keywords:
ADS-B, antenna, microstrip, array, franklin, collinear, power combiner, reflectorAbstract
In this study, an antenna system that could cover the 360ᵒ detection area using the microstrip method was created. The antenna design proposed uses the franklin collinear method with the addition of an array of arms to the left and right of the antenna and the addition of reflectors as a gain enhancer. The four antenna array units are combined using a power divider (combiner) as a unifying antenna. Antenna design with end fire radiation pattern cannot be used in receiving the ADS-B antenna system, because it works only in certain sectors with certain beamwidth, so it needs to be modified by adding an array of 4 units that make up 360◦ radiation of directional diagrams. The addition of the reflector is done by testing the optimum width. The most optimum width is obtained by the width of the side addition on the side of the antenna aperture cross section width of 80 mm. Based on the results of experiments that have been carried out for the design of receiver antennas for ADS-B applications that are required in the form of a radiation pattern in all directions using the reflector technique, the most appropriate gain increase is to use a phase difference for the antennas that are closest both left and right by 90o in ¼ λ conditions in the integration process using a 4 way power combiner. Response return loss at frequency 1.0752 GHz and 1.109 GHz is -15 dB, it means antenna has 33.8 MHz bandwidth with maximum response return loss at -23.22 dB and gain of 7.586 dBi, this antenna design is very suitable for use in the ADS-B application. Design and simulation at this antenna used CST software.Downloads
References
E. A. Suteja, A. D. Prasetyo, B. Satriyotomo, D. H. Dafiq, and Edwar, “ADS-B microstrip antenna receiver design for CubeSat with SLOT,” in 2019 Int. Conf. Inf. Commun. Technol. ICOIACT, Yogyakarta, pp. 17–21, 2019. Crossref
K. J. Matheou, R. D. Apaza, A. N. Downey, R. J. Kerczewski, and J. Wang, “ADS-B mixed SUAS and NAS system capacity analysis and DAA performance,” ICNS 2018 - Integr. Commun. Navig. Surveill. Conf., pp. 2B3-2B31, 2018. Crossref
Y. Nurhayati and S. Susanti, “Implementasi Automatic Dependent Surveillance Broadcast (ADS-B) di Indonesia,” War. Ardhia, vol. 40, no. 3, pp. 147–162, 2014. Crossref
L. Boccia and O. Breinbjerg, “Antenna Basics,” Sp. Antenna Handb., pp. 1–35, 2012.
D. Bhalla and K. Bansal, “Design of a Rectangular Microstrip Patch Antenna Using Inset Feed Technique,” IOSR Journal of Electronics and Communication Engineering (IOSR-JECE), vol. 7, no. 4, pp. 8–13, 2013. Crossref
B. K. Lee and K. Tong, “Microstrip Patch Antennas V Basic Characteristics and Some Recent Advances,” Proceedings of the IEEE, vol. 100, no. 7, pp. 2169–2180, 2012. Crossref
K. Fong and K. Tong, "Microstrip Patch Antennas—Basic Characteristics and Some Recent Advances", Proceedings of the IEEE, vol. 100, no. 7, pp. 2169-2180, 2012.
J. -. Heinola, P. Silventoinen, K. Latti, M. Kettunen and J. -. Strom, "Determination of dielectric constant and dissipation factor of a printed circuit board material using a microstrip ring resonator structure," in 15th International Conference on Microwaves, Radar and Wireless Communications (IEEE Cat. No.04EX824), Warsaw, pp. 202-205, 2004.
S. Wetterlin, “Determination of Dielectric Constant Of Printed Circuit Boards C ⋅ D,” 2010 [Online]. Available: www.semanticscholar.org.
Y. Y. Maulana, Y. P. Saputera, A. B. Santiko, and A. Setiawan, “Compact power divider integrated with coupler and microstrip cavity filter for x-band surveillance radar system,” Telkomnika (Telecommunication Comput. Electron. Control., vol. 15, no. 1, pp. 227–237, 2017.
L. Guo et al., “A high-isolation eight-way Power Combiner,”, IEEE Transactions on Microwave Theory and Techniques, vol. 68, no. 3, pp. 854-866, 2020.
L. Guo, J. Li, W. Huang, H. Shao, and T. Ba, “A Compact Four-Way Power Combiner,” IEEE Microw. Wirel. Components Lett., vol. 27, no. 3, pp. 239–241, 2017.
Downloads
Published
Issue
Section
License
Authors who publish with this journal agree to the following terms:
The copyright to this article is transferred to BRIN if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to BRIN. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment. The copyright transfer form can be downloaded here.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
