Band-Pass Filter Microstrip at 3 GHz Frequency Using Square Open-Loop Resonator for S-Band Radar Applications
DOI:
https://doi.org/10.14203/jet.v20.53-59Keywords:
bandpass filter, filter, microstrip, square open-loop resonatorAbstract
In telecommunication, filters are often used to pass the desired frequency. One of them is the Band-Pass Filter (BPF) which is passing signals between the upper cut-off frequency and the lower cut-off frequency. This research aims to make a band-pass filter that can pass 3 GHz frequency with a bandwidth of 200 MHz. This filter is designed with a square open-loop resonator simulated using Advanced Design System (ADS) software. The filter is made using FR 4-epoxy substrates with a dielectric constant (ε ) of 4.6 and substrate thickness (h) of 1.6 mm. Based on the simulation results obtained in the form of a comparison graph between the response of magnitude to frequency, it shows that the value of the return loss (S 11 ) parameter of -23.549 dB, insertion loss (S 21 ) parameter value of -1.397 dB, and a slightly shifted middle frequency of 2.890 GHz. Then for the measurement results obtained a parameter value return loss (S 11 ) of -16.364 dB, parameter value insertion loss (S 21 ) of -3.561 dB with a center frequency of 3.185 GHz.
Downloads
References
J. S. Hong, Microstrip Filters for RF/Microwave Applications, 2nd ed. NY: John Wiley & Sons, Inc., 2011.
B. U. Suryaningsih, A. A. Muayyadi, and E. Sulaeman "Perancangan dan realisasi bandpass filter yang bekerja pada frekuensi 3 GHz menggunakan metode hairpin," in e-Proc. Eng., vol. 4, no. 1, 2017, pp. 492-499.
T. Praludi, Y. Sulaeman, Y. Taryana, and B. E. Sukoco, "Bandpass filter microstrip using octagonal shape for S-band radar," in 2017 Int. Conf. Radar Antenna Microw. Electron. Telecommun., 2017. Crossref
D. Adithama, H. Wijanto, Y. Wahyu, "Filter bandpass hairpin dengan defected ground structure untuk synthetic aperture radar 1.27 GHz," in e-Proc. Eng., vol. 4, no. 3, 2017, p. 3422.
D. A. Letavin, "Bandpass filters on U-shaped resonator," in 19th Int. Conf. Micro/nanotechnol. Electron Devices EDM 2018, 2018.
M. Khajavi, and M. Shakiba, "Compact microstrip dual-band bandpass filter using step impedance resonators," in 27th Iranian Conf. Elect. Eng., 2019. Crossref
R. Y. Aditya, and M. Alaydrus, “Perancangan mikrostrip band-pass filter pada frekuensi 3.3 GHz dengan menggunakan defected ground structure”, Universitas Mercu Buana, 2016.
A. B. Santiko, Y. S. Amrullah, Y. Wahyu, M. I. Maulana and B. Setia, “Design and realization of coupled line bandpass filter using compact structure at frequencies of 3300 MHz – 3400 MHz for WiMAX application,” Jurnal Elektronika Telekomunikasi vol. 16, no. 1, pp. 11-14, 2016. Crossref
N. A. D. Ayuni, A. Atmaja, and K. Wardani, "Rancang bangun antena mikrostrip circular patch metode array 4 elemen sebagai penerima TV UHF," Jurnal Ilmu Pengetahuan Teknologi, vol. 2, no. 1, pp. 22-31, 2018.
Pattimura University Ambon, Proceedings the 4th International Conference on Basic Sciences 2018: The Development of Sciences and Technology in Improving Natural and Cultural Resources. Ambon: Universitas Pattimura Ambon, 2019.
E. Hammerstad and O. Jensen, “Accurate models for microstrip computer-aided design,” in 1980 IEEE MTT-S Int. Microw. Symp. Dig., 1980, pp. 407-409. Crossref
H. A. Wheeler, “Transmission-line properties of parallel strips separated by a dielectric sheet”, IEEE Trans. Microw. Theory Techniques, vol. 13, no. 2, 1965. Crossref
E. O. Hammerstad, "Equations for microstrip circuit design," in 1975 5th European Microw. Conf., Germany, 1975.
Mini-Circuits, Appl. Note DG03-111, p. 111
Downloads
Published
Issue
Section
License
Authors who publish with this journal agree to the following terms:
The copyright to this article is transferred to BRIN if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to BRIN. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment. The copyright transfer form can be downloaded here.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
